set_bead_inspection_paramset_bead_inspection_paramSetBeadInspectionParamset_bead_inspection_paramSetBeadInspectionParamSetBeadInspectionParam (Operator)

Name

set_bead_inspection_paramset_bead_inspection_paramSetBeadInspectionParamset_bead_inspection_paramSetBeadInspectionParamSetBeadInspectionParam — Set parameters of the bead inspection model.

Signature

Description

The operator set_bead_inspection_paramset_bead_inspection_paramSetBeadInspectionParamset_bead_inspection_paramSetBeadInspectionParamSetBeadInspectionParam is used to set parameters of a bead inspection model in order to adapt it to a particular inspection task. All parameters except for the model's contour can be set with this operator. A new bead inspection model should be used when a new contour is introduced. The current values of all parameters can be queried with the operator get_bead_inspection_paramget_bead_inspection_paramGetBeadInspectionParamget_bead_inspection_paramGetBeadInspectionParamGetBeadInspectionParam.

Parameters that can be set

The following parameters are essential and inspection model specific. It is vital for the inspection's success to identify accurate values for those parameters:

'target_thickness'"target_thickness""target_thickness""target_thickness""target_thickness""target_thickness":

sets the TargetThicknessTargetThicknessTargetThicknessTargetThicknessTargetThicknesstargetThickness.

'thickness_tolerance'"thickness_tolerance""thickness_tolerance""thickness_tolerance""thickness_tolerance""thickness_tolerance":

sets the ThicknessToleranceThicknessToleranceThicknessToleranceThicknessToleranceThicknessTolerancethicknessTolerance.

'position_tolerance'"position_tolerance""position_tolerance""position_tolerance""position_tolerance""position_tolerance":

sets the PositionTolerancePositionTolerancePositionTolerancePositionTolerancePositionTolerancepositionTolerance.

'polarity'"polarity""polarity""polarity""polarity""polarity":

sets the bead's PolarityPolarityPolarityPolarityPolaritypolarity.

'sigma'"sigma""sigma""sigma""sigma""sigma"

'threshold'"threshold""threshold""threshold""threshold""threshold"

For more details, refer to the parameters' description in create_bead_inspection_modelcreate_bead_inspection_modelCreateBeadInspectionModelcreate_bead_inspection_modelCreateBeadInspectionModelCreateBeadInspectionModel.

Parallelization

• Multithreading type: reentrant (runs in parallel with non-exclusive operators).
• Multithreading scope: global (may be called from any thread).
• Processed without parallelization.

This operator modifies the state of the following input parameter:

• BeadInspectionModelBeadInspectionModelBeadInspectionModelBeadInspectionModelBeadInspectionModelbeadInspectionModel

Parameters

Result

The operator set_bead_inspection_paramset_bead_inspection_paramSetBeadInspectionParamset_bead_inspection_paramSetBeadInspectionParamSetBeadInspectionParam returns the value 2 (H_MSG_TRUE) if the given parameters are valid and within acceptable range. Otherwise, an exception will be raised.

Possible Predecessors

create_bead_inspection_modelcreate_bead_inspection_modelCreateBeadInspectionModelcreate_bead_inspection_modelCreateBeadInspectionModelCreateBeadInspectionModel

Possible Successors

apply_bead_inspection_modelapply_bead_inspection_modelApplyBeadInspectionModelapply_bead_inspection_modelApplyBeadInspectionModelApplyBeadInspectionModel, get_bead_inspection_paramget_bead_inspection_paramGetBeadInspectionParamget_bead_inspection_paramGetBeadInspectionParamGetBeadInspectionParam

Alternatives

create_bead_inspection_modelcreate_bead_inspection_modelCreateBeadInspectionModelcreate_bead_inspection_modelCreateBeadInspectionModelCreateBeadInspectionModel

See also

create_bead_inspection_modelcreate_bead_inspection_modelCreateBeadInspectionModelcreate_bead_inspection_modelCreateBeadInspectionModelCreateBeadInspectionModel, clear_bead_inspection_modelclear_bead_inspection_modelClearBeadInspectionModelclear_bead_inspection_modelClearBeadInspectionModelClearBeadInspectionModel

Module

2D Metrology