gen_image_to_world_plane_map — Generate a projection map that describes the mapping between the image
plane and the plane z=0 of a world coordinate system.
gen_image_to_world_plane_map generates a projection map
which describes the mapping between the image plane and the plane z=0
(plane of measurements) in a world coordinate system. This map can be used
to rectify an image with the operator
map_image. The rectified
image shows neither radial nor perspective distortions; it corresponds to
an image acquired by a distortion-free camera that looks perpendicularly
onto the plane of measurements. The world coordinate system (wcs)
is chosen by passing its 3D pose relative to the camera coordinate system
WorldPose. Thus the pose is expected in the form
(see Transformations / Poses
“Solution Guide III-C - 3D Vision”).
CameraParam you must pass the internal camera
parameters (see Calibration for the sequence of the
parameters and the underlying camera model).
In many cases
WorldPose are the result of
calibrating the camera with the operator
below for an example.
The size of the images to be mapped can be specified by the parameters
HeightIn. The pixel position of the upper left
corner of the output image is determined by the origin of the world
coordinate system. The size of the output image can be chosen by the
HeightMapped must be given
Scale can be used to specify the size of a pixel in the
transformed image. There are two ways to use this parameter:
Scale the image such that one pixel in the transformed image corresponds to a metric unit, e.g., setting 'mm' determines that a pixel in the transformed image corresponds to the area 1mm x 1mm in the plane of measurements. For this, the original unit needs to be meters. This is the case if you use a standard calibration plate.
List of values: 'm', 'cm', 'mm', 'microns', 'um'.
Scale the image by giving a number that determines the ratio of original unit length / desired number of pixels. E.g., if your original unit is meters and you want every pixel of your transformed image to represent 3mm x 3mm of the measuring plane, your scale is calculated . If you want to perform a task like shape-based matching on your transformed image, it is useful to scale the image such that its content appears in a size similar to the original image.
Scale > 0.
The mapping function is stored in the output image
Map has the same size as the resulting images after the mapping.
MapType is used to specify the type of the output
If 'nearest_neighbor' is chosen,
Map consists of one image
containing one channel, in which for each pixel of the resulting image the
linearized coordinate of the pixel of the input image is stored that is the
nearest neighbor to the transformed coordinates. If 'bilinear'
interpolation is chosen,
Map consists of one image containing five
channels. In the first channel for each pixel in the resulting image the
linearized coordinates of the pixel in the input image is stored that is in
the upper left position relative to the transformed coordinates.
The four other channels contain the weights of the four neighboring pixels
of the transformed coordinates which are used for the bilinear
interpolation, in the following order:
The second channel, for example, contains the weights of the pixels that
lie to the upper left relative to the transformed coordinates.
If 'coord_map_sub_pix' is chosen,
Map consists of
one vector field image of the semantic type 'vector_field_absolute', in
which for each pixel of the resulting image the subpixel precise
coordinates in the input image are stored.
If several images have to be mapped using the same camera parameters,
gen_image_to_world_plane_map in combination with
is much more efficient than the operator
because the mapping function needs to be computed only once.
If you want to re-use the created map in another program, you can save it as
a multi-channel image with the operator
write_image, using the
→object (int4 / int8 / uint2 / vector_field)
Image containing the mapping data.
→(real / integer / string)
Internal camera parameters.
→(real / integer)
3D pose of the world coordinate system in camera coordinates.
Number of elements: 7
Width of the images to be transformed.
WidthIn >= 1
Height of the images to be transformed.
HeightIn >= 1
Width of the resulting mapped images in pixels.
WidthMapped >= 1
Height of the resulting mapped images in pixels.
HeightMapped >= 1
→(string / integer / real)
Scale or unit.
Default value: 'm'
Suggested values: 'm', 'cm', 'mm', 'microns', 'um', 1.0, 0.01, 0.001, 1.0e-6, 0.0254, 0.3048, 0.9144
Scale > 0
Type of the mapping.
Default value: 'bilinear'
List of values: 'bilinear', 'coord_map_sub_pix', 'nearest_neighbor'
* Calibrate camera. calibrate_cameras (CalibDataID, Error) * Obtain camera parameters. get_calib_data (CalibDataID, 'camera', 0, 'params', CamParam) * Example values, if no calibration data is available: CamParam := ['area_scan_division', 0.0087, -1859, 8.65e-006, 8.6e-006, \ 362.5, 291.6, 768, 576] * Get reference pose (pose 4 of calibration object 0). get_calib_data (CalibDataID, 'calib_obj_pose',\ [0,4], 'pose', Pose) * Example values, if no calibration data is available: Pose := [-0.11, -0.21, 2.51, 352.73, 346.73, 336.48, 0] * Compensate thickness of plate. set_origin_pose (Pose, -1.125, -1.0, 0, PoseNewOrigin) * Transform the image into the world plane. read_image (Image, 'calib/calib-3d-coord-04') gen_image_to_world_plane_map (MapSingle, CamParam, PoseNewOrigin,\ CamParam, CamParam, 900, 800, 0.0025, 'bilinear') map_image (Image, MapSingle, ImageMapped)
gen_image_to_world_plane_map returns TRUE if all parameter values
are correct. If necessary, an exception is raised.