HALCON Website / HALCON Operator Reference / 1D Measuring
ClassesClasses | | Operators

gen_measure_arcT_gen_measure_arcGenMeasureArcGenMeasureArcgen_measure_arc (Operator)

Name

gen_measure_arcT_gen_measure_arcGenMeasureArcGenMeasureArcgen_measure_arc — Prepare the extraction of straight edges perpendicular to an annular arc.

Signature

gen_measure_arc( : : CenterRow, CenterCol, Radius, AngleStart, AngleExtent, AnnulusRadius, Width, Height, Interpolation : MeasureHandle)

Herror T_gen_measure_arc(const Htuple CenterRow, const Htuple CenterCol, const Htuple Radius, const Htuple AngleStart, const Htuple AngleExtent, const Htuple AnnulusRadius, const Htuple Width, const Htuple Height, const Htuple Interpolation, Htuple* MeasureHandle)

void GenMeasureArc(const HTuple& CenterRow, const HTuple& CenterCol, const HTuple& Radius, const HTuple& AngleStart, const HTuple& AngleExtent, const HTuple& AnnulusRadius, const HTuple& Width, const HTuple& Height, const HTuple& Interpolation, HTuple* MeasureHandle)

void HMeasure::HMeasure(const HTuple& CenterRow, const HTuple& CenterCol, const HTuple& Radius, const HTuple& AngleStart, const HTuple& AngleExtent, const HTuple& AnnulusRadius, Hlong Width, Hlong Height, const HString& Interpolation)

void HMeasure::HMeasure(double CenterRow, double CenterCol, double Radius, double AngleStart, double AngleExtent, double AnnulusRadius, Hlong Width, Hlong Height, const HString& Interpolation)

void HMeasure::HMeasure(double CenterRow, double CenterCol, double Radius, double AngleStart, double AngleExtent, double AnnulusRadius, Hlong Width, Hlong Height, const char* Interpolation)

void HMeasure::HMeasure(double CenterRow, double CenterCol, double Radius, double AngleStart, double AngleExtent, double AnnulusRadius, Hlong Width, Hlong Height, const wchar_t* Interpolation)   (Windows only)

void HMeasure::GenMeasureArc(const HTuple& CenterRow, const HTuple& CenterCol, const HTuple& Radius, const HTuple& AngleStart, const HTuple& AngleExtent, const HTuple& AnnulusRadius, Hlong Width, Hlong Height, const HString& Interpolation)

void HMeasure::GenMeasureArc(double CenterRow, double CenterCol, double Radius, double AngleStart, double AngleExtent, double AnnulusRadius, Hlong Width, Hlong Height, const HString& Interpolation)

void HMeasure::GenMeasureArc(double CenterRow, double CenterCol, double Radius, double AngleStart, double AngleExtent, double AnnulusRadius, Hlong Width, Hlong Height, const char* Interpolation)

void HMeasure::GenMeasureArc(double CenterRow, double CenterCol, double Radius, double AngleStart, double AngleExtent, double AnnulusRadius, Hlong Width, Hlong Height, const wchar_t* Interpolation)   (Windows only)

static void HOperatorSet.GenMeasureArc(HTuple centerRow, HTuple centerCol, HTuple radius, HTuple angleStart, HTuple angleExtent, HTuple annulusRadius, HTuple width, HTuple height, HTuple interpolation, out HTuple measureHandle)

public HMeasure(HTuple centerRow, HTuple centerCol, HTuple radius, HTuple angleStart, HTuple angleExtent, HTuple annulusRadius, int width, int height, string interpolation)

public HMeasure(double centerRow, double centerCol, double radius, double angleStart, double angleExtent, double annulusRadius, int width, int height, string interpolation)

void HMeasure.GenMeasureArc(HTuple centerRow, HTuple centerCol, HTuple radius, HTuple angleStart, HTuple angleExtent, HTuple annulusRadius, int width, int height, string interpolation)

void HMeasure.GenMeasureArc(double centerRow, double centerCol, double radius, double angleStart, double angleExtent, double annulusRadius, int width, int height, string interpolation)

def gen_measure_arc(center_row: Union[int, float], center_col: Union[int, float], radius: Union[int, float], angle_start: Union[int, float], angle_extent: Union[int, float], annulus_radius: Union[int, float], width: int, height: int, interpolation: str) -> HHandle

Description

gen_measure_arcgen_measure_arcGenMeasureArcGenMeasureArcGenMeasureArcgen_measure_arc prepares the extraction of straight edges which lie perpendicular to an annular arc. Here, annular arc denotes a circular arc with an associated width. The center of the arc is passed in the parameters CenterRowCenterRowCenterRowCenterRowcenterRowcenter_row and CenterColCenterColCenterColCenterColcenterColcenter_col, its radius in RadiusRadiusRadiusRadiusradiusradius, the starting angle in AngleStartAngleStartAngleStartAngleStartangleStartangle_start, and its angular extent relative to the starting angle in AngleExtentAngleExtentAngleExtentAngleExtentangleExtentangle_extent. If AngleExtentAngleExtentAngleExtentAngleExtentangleExtentangle_extent > 0, an arc with counterclockwise orientation is generated, otherwise an arc with clockwise orientation. The radius of the annular arc, i.e., half its width, is determined by AnnulusRadiusAnnulusRadiusAnnulusRadiusAnnulusRadiusannulusRadiusannulus_radius.

For an explanation of the concept of 1D measuring see the introduction of chapter 1D Measuring.

The edge extraction algorithm is described in the documentation of the operator measure_posmeasure_posMeasurePosMeasurePosMeasurePosmeasure_pos. As discussed there, different types of interpolation can be used for the calculation of the one-dimensional gray value profile. For InterpolationInterpolationInterpolationInterpolationinterpolationinterpolation = 'nearest_neighbor'"nearest_neighbor""nearest_neighbor""nearest_neighbor""nearest_neighbor""nearest_neighbor", the gray values in the measurement are obtained from the gray values of the closest pixel, i.e., by constant interpolation. For InterpolationInterpolationInterpolationInterpolationinterpolationinterpolation = 'bilinear'"bilinear""bilinear""bilinear""bilinear""bilinear", bilinear interpolation is used, while for InterpolationInterpolationInterpolationInterpolationinterpolationinterpolation = 'bicubic'"bicubic""bicubic""bicubic""bicubic""bicubic", bicubic interpolation is used.

To perform the actual measurement at optimal speed, all computations that can be used for multiple measurements are already performed in the operator gen_measure_arcgen_measure_arcGenMeasureArcGenMeasureArcGenMeasureArcgen_measure_arc. For this, an optimized data structure, a so-called measure object, is constructed and returned in MeasureHandleMeasureHandleMeasureHandleMeasureHandlemeasureHandlemeasure_handle. The size of the images in which measurements will be performed must be specified in the parameters WidthWidthWidthWidthwidthwidth and HeightHeightHeightHeightheightheight.

The system parameter 'int_zooming'"int_zooming""int_zooming""int_zooming""int_zooming""int_zooming" (see set_systemset_systemSetSystemSetSystemSetSystemset_system) affects the accuracy and speed of the calculations used to construct the measure object. If 'int_zooming'"int_zooming""int_zooming""int_zooming""int_zooming""int_zooming" is set to 'true'"true""true""true""true""true", the internal calculations are performed using fixed point arithmetic, leading to much shorter execution times. However, the geometric accuracy is slightly lower in this mode. If 'int_zooming'"int_zooming""int_zooming""int_zooming""int_zooming""int_zooming" is set to 'false'"false""false""false""false""false", the internal calculations are performed using floating point arithmetic, leading to the maximum geometric accuracy, but also to significantly increased execution times.

Attention

Note that when using bilinear or bicubic interpolation, not only the measurement rectangle but additionally the margin around the rectangle must fit into the image. The width of the margin (in all four directions) must be at least one pixel for bilinear interpolation and two pixels for bicubic interpolation. For projection lines that do not fulfill this condition, no gray value is computed. Thus, no edge can be extracted at these positions.

Please also note that the center coordinates of the arc are rounded internally, so that the center lies on the pixel grid. This is done to ensure consistency.

Execution Information

This operator returns a handle. Note that the state of an instance of this handle type may be changed by specific operators even though the handle is used as an input parameter by those operators.

Parameters

CenterRowCenterRowCenterRowCenterRowcenterRowcenter_row (input_control)  point.y → HTupleUnion[int, float]HTupleHtuple (real / integer) (double / int / long) (double / Hlong) (double / Hlong)

Row coordinate of the center of the arc.

Default value: 100.0

Suggested values: 10.0, 20.0, 50.0, 100.0, 200.0, 300.0, 400.0, 500.0

Typical range of values: 0.0 ≤ CenterRow CenterRow CenterRow CenterRow centerRow center_row ≤ 511.0 (lin)

Minimum increment: 1.0

Recommended increment: 10.0

CenterColCenterColCenterColCenterColcenterColcenter_col (input_control)  point.x → HTupleUnion[int, float]HTupleHtuple (real / integer) (double / int / long) (double / Hlong) (double / Hlong)

Column coordinate of the center of the arc.

Default value: 100.0

Suggested values: 10.0, 20.0, 50.0, 100.0, 200.0, 300.0, 400.0, 500.0

Typical range of values: 0.0 ≤ CenterCol CenterCol CenterCol CenterCol centerCol center_col ≤ 511.0 (lin)

Minimum increment: 1.0

Recommended increment: 10.0

RadiusRadiusRadiusRadiusradiusradius (input_control)  number → HTupleUnion[int, float]HTupleHtuple (real / integer) (double / int / long) (double / Hlong) (double / Hlong)

Radius of the arc.

Default value: 50.0

Suggested values: 10.0, 20.0, 50.0, 100.0, 200.0, 300.0, 400.0, 500.0

Typical range of values: 0.0 ≤ Radius Radius Radius Radius radius radius ≤ 511.0 (lin)

Minimum increment: 1.0

Recommended increment: 10.0

AngleStartAngleStartAngleStartAngleStartangleStartangle_start (input_control)  angle.rad → HTupleUnion[int, float]HTupleHtuple (real / integer) (double / int / long) (double / Hlong) (double / Hlong)

Start angle of the arc in radians.

Default value: 0.0

Suggested values: -3.14159, -2.35619, -1.57080, -0.78540, 0.0, 0.78540, 1.57080, 2.35619, 3.14159

Typical range of values: -3.14159 ≤ AngleStart AngleStart AngleStart AngleStart angleStart angle_start ≤ 3.14159 (lin)

Minimum increment: 0.03142

Recommended increment: 0.31416

AngleExtentAngleExtentAngleExtentAngleExtentangleExtentangle_extent (input_control)  angle.rad → HTupleUnion[int, float]HTupleHtuple (real / integer) (double / int / long) (double / Hlong) (double / Hlong)

Angular extent of the arc in radians.

Default value: 6.28318

Suggested values: -6.28318, -5.49779, -4.71239, -3.92699, -3.14159, -2.35619, -1.57080, -0.78540, 0.78540, 1.57080, 2.35619, 3.14159, 3.92699, 4.71239, 5.49779, 6.28318

Typical range of values: -6.28318 ≤ AngleExtent AngleExtent AngleExtent AngleExtent angleExtent angle_extent ≤ 6.28318 (lin)

Minimum increment: 0.03142

Recommended increment: 0.31416

Restriction: AngleExtent != 0.0

AnnulusRadiusAnnulusRadiusAnnulusRadiusAnnulusRadiusannulusRadiusannulus_radius (input_control)  number → HTupleUnion[int, float]HTupleHtuple (real / integer) (double / int / long) (double / Hlong) (double / Hlong)

Radius (half width) of the annulus.

Default value: 10.0

Suggested values: 10.0, 20.0, 50.0, 100.0, 200.0, 300.0, 400.0, 500.0

Typical range of values: 0.0 ≤ AnnulusRadius AnnulusRadius AnnulusRadius AnnulusRadius annulusRadius annulus_radius ≤ 511.0 (lin)

Minimum increment: 1.0

Recommended increment: 10.0

Restriction: AnnulusRadius <= Radius

WidthWidthWidthWidthwidthwidth (input_control)  extent.x → HTupleintHTupleHtuple (integer) (int / long) (Hlong) (Hlong)

Width of the image to be processed subsequently.

Default value: 512

Suggested values: 128, 160, 192, 256, 320, 384, 512, 640, 768

Typical range of values: 0 ≤ Width Width Width Width width width ≤ 1024 (lin)

Minimum increment: 1

Recommended increment: 16

HeightHeightHeightHeightheightheight (input_control)  extent.y → HTupleintHTupleHtuple (integer) (int / long) (Hlong) (Hlong)

Height of the image to be processed subsequently.

Default value: 512

Suggested values: 120, 128, 144, 240, 256, 288, 480, 512, 576

Typical range of values: 0 ≤ Height Height Height Height height height ≤ 1024 (lin)

Minimum increment: 1

Recommended increment: 16

InterpolationInterpolationInterpolationInterpolationinterpolationinterpolation (input_control)  string → HTuplestrHTupleHtuple (string) (string) (HString) (char*)

Type of interpolation to be used.

Default value: 'nearest_neighbor' "nearest_neighbor" "nearest_neighbor" "nearest_neighbor" "nearest_neighbor" "nearest_neighbor"

List of values: 'bicubic'"bicubic""bicubic""bicubic""bicubic""bicubic", 'bilinear'"bilinear""bilinear""bilinear""bilinear""bilinear", 'nearest_neighbor'"nearest_neighbor""nearest_neighbor""nearest_neighbor""nearest_neighbor""nearest_neighbor"

MeasureHandleMeasureHandleMeasureHandleMeasureHandlemeasureHandlemeasure_handle (output_control)  measure → HMeasure, HTupleHHandleHTupleHtuple (handle) (IntPtr) (HHandle) (handle)

Measure object handle.

Result

If the parameter values are correct, the operator gen_measure_arcgen_measure_arcGenMeasureArcGenMeasureArcGenMeasureArcgen_measure_arc returns the value 2 (H_MSG_TRUE). Otherwise an exception is raised.

Possible Predecessors

draw_circledraw_circleDrawCircleDrawCircleDrawCircledraw_circle

Possible Successors

measure_posmeasure_posMeasurePosMeasurePosMeasurePosmeasure_pos, measure_pairsmeasure_pairsMeasurePairsMeasurePairsMeasurePairsmeasure_pairs, fuzzy_measure_posfuzzy_measure_posFuzzyMeasurePosFuzzyMeasurePosFuzzyMeasurePosfuzzy_measure_pos, fuzzy_measure_pairsfuzzy_measure_pairsFuzzyMeasurePairsFuzzyMeasurePairsFuzzyMeasurePairsfuzzy_measure_pairs, fuzzy_measure_pairingfuzzy_measure_pairingFuzzyMeasurePairingFuzzyMeasurePairingFuzzyMeasurePairingfuzzy_measure_pairing

Alternatives

edges_sub_pixedges_sub_pixEdgesSubPixEdgesSubPixEdgesSubPixedges_sub_pix

See also

gen_measure_rectangle2gen_measure_rectangle2GenMeasureRectangle2GenMeasureRectangle2GenMeasureRectangle2gen_measure_rectangle2

Module

1D Metrology

ClassesClasses | | Operators
HALCON Operator Reference 22.05.0.0 Copyright © 1996-2022 MVTec Software GmbH
Follow us on