get_rectangle_pose — Determine the 3D pose of a rectangle from its perspective 2D
A rectangle in space is projected as a general quadrangle into the
get_rectangle_pose determines the
the rectangle from this projection (
The algorithm works as follows: First,
Contour is segmented
into four line segments and their intersections are considered as
corners of the contour. The corners together with the internal
camera parameters (
CameraParam) and the rectangle size in
Height) are used for an initial
estimation of the rectangle pose. Then, the final
refined with a non-linear optimization by minimizing the geometrical
distance of the contour points from the back projection of the
rectangle in the image.
The operator supports only area scan pinhole (projective)
cameras. An error is returned if
CameraParam specifies a
line scan or a telecentric camera (see also
Height specify the size of the rectangle
in x and y dimensions, respectively, in its coordinate
system. The origin of this coordinate system is in the center of the
rectangle. The z axis points away from the camera.
be used to damp the impact of outliers on the algorithm. If
WeightingMode is set to 'tukey' or 'huber',
the contour points are weighted based on the approach of Tukey or Huber
respectively. In such a case a robust error statistics is used to
estimate the standard deviation of the distances of the contour
points from the backprojected rectangle excluding outliers. The
ClippingFactor (a scaling factor for the standard
deviation) controls the amount of damping outliers: The smaller the
value chosen for
ClippingFactor the more outliers are
detected. See a discussion about the properties of the different
weighting modes in
fit_line_contour_xld. Note that, unlike
fit_line_contour_xld, for the rectangle pose estimation
the approach of Huber is recommended.
Poseis of code-0 (see
create_pose) and represents the pose of the center of the rectangle. You can compute the pose of the corners of the rectangle as follows:
Poseare normalized to be in the range [-90; 90] degrees and the rest of the 4 possible poses can be computed by combining flips around the corresponding axis:
Note that if the rectangle is a square (
Height) the number of alternative poses is 8.
If more than one contour are given in
corresponding tuple of values for both
Height has to be provided as well. Yet, if only one value
is provided for each of these arguments, then this value is applied
for each processed contour. A pose is estimated for each processed
contour and all poses are concatenated in
Pose (see the
The accuracy of the estimated pose depends on the following three factors:
In order to achieve an accurate pose estimation, there are three corresponding criteria that should be considered:
For a rectangular object deviating from this criterion, its longer
side dominates the determination of its pose. This causes
instability in the estimation of the angle around the longer
rectangle's axis. In the extreme case when one of the dimensions is
0, the rectangle is in fact a line segment, whose pose cannot be
Secondly, the lengths of each side of the contour should be at least 20 pixels. An error is returned if a side of the contour is less than 5 pixels long.
Thirdly, the more the contour appears projectively distorted, the more stable the algorithm works. Therefore, the pose of a rectangle tilted with respect to the image plane can be estimated accurately, whereas the pose of an rectangle parallel to the image plane of the camera could be unstable. This is further discussed in the next paragraph. Additionally, there is a rule of thumb that ensures projective distortion: the rectangle should be placed in space such that its size in x and y dimension in the camera coordinate system should not be less than 1/10th of its distance from the camera in z direction.
get_rectangle_pose provides two measures for the accuracy of
Error is the average pixel
error between the contour points and the modeled rectangle
backprojected on the image. If
Error is exceeding 0.5, this
is an indication that the algorithm did not converge properly, and
Pose should not be used.
contains 36 entries representing the 6×6
covariance matrix of the first 6 entries of
Pose. The above
mentioned case of instability of the angle about the longer
rectangle's axis be detected by checking that the absolute values of
the variances and covariances of the rotations around the x and
y axis (
CovPose) do not exceed
0.05. Further, unusually increased values of any of the covariances
and especially of the variances (the 6 values on the diagonal of
CovPose with indices 0, 7, 14, 21, 28 and 35, respectively)
indicate a poor quality of
Contour(s) to be examined.
→(real / integer / string)
Internal camera parameters.
Width of the rectangle in meters.
Width > 0
Height of the rectangle in meters.
Height > 0
Weighting mode for the optimization phase.
Default value: 'nonweighted'
List of values: 'huber', 'nonweighted', 'tukey'
Clipping factor for the elimination of outliers (typical: 1.0 for 'huber' and 3.0 for 'tukey').
Default value: 2.0
Suggested values: 1.0, 1.5, 2.0, 2.5, 3.0
ClippingFactor > 0
→(real / integer)
3D pose of the rectangle.
Number of elements: Pose == 7 * Contour
Covariances of the pose values.
Number of elements: CovPose == 36 * Contour
Root-mean-square value of the final residual error.
Number of elements: Error == Contour
* Process an image with several rectangles of the same size appearing * as light objects. RectWidth := 0.04 RectHeight := 0.025 gen_cam_par_area_scan_division (0.014, 830, 4.58e-006, 4.65e-006, \ 509, 488, 800, 800, CameraParam) read_image (Image, 'barcode/ean13/tea_box_01') * Find light objects in the image. mean_image (Image, ImageMean, 201, 201) dyn_threshold (Image, ImageMean, Region, 5, 'light') * Fill gaps in the objects. fill_up (Region, RegionFillUp) * Extract rectangular contours. connection (RegionFillUp, ConnectedRegions) select_shape (ConnectedRegions, SelectedRegions, ['area','rectangularity'], \ 'and', [50000,0.9], [640000,1]) boundary (SelectedRegions, RegionBorder, 'inner') dilation_circle (RegionBorder, RegionDilation, 3.5) * NOTE: for a real application, this step might require some additional * pre- or postprocessing. reduce_domain (Image, RegionDilation, ImageReduced) edges_sub_pix (ImageReduced, Edges, 'canny', 1, 20, 40) * Get the pose of all contours found. get_rectangle_pose (Edges, CameraParam, RectWidth, RectHeight, 'huber', 2, \ Poses, CovPose, Error) NumPoses := |Poses|/7 for I := 0 to NumPoses-1 by 1 Pose := Poses[I*7:I*7+6] * Use the Pose here. * ... endfor
get_rectangle_pose returns 2 (H_MSG_TRUE) if all parameter values are
correct and the position of the rectangle has been determined
successfully. If the provided contour(s) cannot be segmented as a
H_ERR_FIT_QUADRANGLE. If further necessary, an exception is
G.Schweighofer and A.Pinz: “Robust Pose Estimation from a Planar Target”; Transactions on Pattern Analysis and Machine Intelligence (PAMI), 28(12):2024-2030, 2006