Multi-View

List of Operators ↓

This chapter describes how to calibrate different multi-view camera setups.

In order to achieve high accuracy for your measuring tasks you need to calibrate your camera setup. In comparison to a single-camera setup, some additional requirements apply to the calibration of a multi-view camera setup. The following paragraphs provide explanations regarding the calibration of multi-view camera setups. For general information on camera calibration please refer to the chapter Calibration.

Preparing the Calibration Input Data for Multi-View Camera Setups

Before the actual calibration can be performed, a calibration data model must be prepared (as described in Calibration). For setups with multiple cameras, these additional aspects should be considered:

Performing the Actual Camera Calibration

The calibration performed by calibrate_camerascalibrate_camerasCalibrateCamerasCalibrateCamerasCalibrateCamerascalibrate_cameras depends on the camera types that are involved in the calibration setup. While different camera setups require specific conditions when acquiring images, the basic steps of the calibration procedure for setups including projective and/or telecentric cameras are similar:

  1. Building a chain of observation poses: In the first step, the operator calibrate_camerascalibrate_camerasCalibrateCamerasCalibrateCamerasCalibrateCamerascalibrate_cameras tries to build a valid chain of observation poses, that connects all cameras and calibration object poses to the reference camera. Depending on the setup, the conditions for a valid chain of poses differ. For specific information see the respective paragraphs below.

    If there is a camera that cannot be reached (i.e., it is not observing any calibration object pose that can be connected in the chain), the calibration process is terminated with an error. Otherwise, the algorithm initializes all calibration items' poses by going down this chain.

  2. First optimization: In this step, calibrate_camerascalibrate_camerasCalibrateCamerasCalibrateCamerasCalibrateCamerascalibrate_cameras performs the actual optimization for all optimization parameters that were not explicitly excluded from the calibration.

  3. Second optimization: Based on the so-far calibrated cameras, the algorithm corrects all observations that contain mark contour information (see find_calib_objectfind_calib_objectFindCalibObjectFindCalibObjectFindCalibObjectfind_calib_object). Then, the calibration setup is optimized anew for the corrections to take effect. If no contour information was available, this step is skipped.

  4. Compute quality of parameter estimation: In the last step, calibrate_camerascalibrate_camerasCalibrateCamerasCalibrateCamerasCalibrateCamerascalibrate_cameras computes the standard deviations and the covariances of the calibrated internal camera parameters.

The following paragraphs give further information about the conditions specific to the camera setups.

Projective area scan cameras

For a setup with projective area scan cameras, the calibration is performed in the four steps listed above. The algorithm tries to build a chain of observation poses that connects all cameras and calibration object poses to the reference camera like in the diagram below.

image/svg+xml image/svg+xml
(1) (2)
(1) All cameras can be connected by a chain of observation poses. (2) The leftmost camera is isolated, because the left calibration plate cannot be seen by any other camera.

Possible projective area scan cameras are:

Telecentric area scan cameras

For a setup with telecentric area scan cameras, similar to projective area scan cameras, the same four steps that are listed above are executed. In the first step (building a chain of observation poses that connects all cameras and calibration objects), additional conditions must hold. Since the pose of an object can only be determined up to a translation along the optical axis, each calibration object must be observed by at least two cameras to determine its relative location. Otherwise, its pose is excluded from the calibration. Also, since a planar calibration object appears the same from two different observation angles, the relative pose of the cameras among each other cannot be determined unambiguously. Therefore, there are always two valid alternative relative poses. Both alternatives result in a consistent camera setup which can be used for measuring. Since the ambiguity cannot be resolved, the first of the alternatives is returned. Note that, if the returned pose is not the real pose but the alternative one, then this will result in a mirrored reconstruction.

Possible telecentric area scan cameras are:

Projective and telecentric area scan cameras

For a mixed setup with projective and telecentric area scan cameras, the algorithm performs the same four steps as enumerated above. Possible ambiguities during the first step (building a chain of observation poses that connects all cameras and calibration objects), as described above for the setup with telecentric cameras, can be resolved as long as there exists a chain of observation poses consisting of all perspective cameras and a sufficient number of calibration objects. Here, sufficient number means that each telecentric camera observes at least two calibration objects of this chain.

image/svg+xml (P) (T) (P) image/svg+xml (P) (T) (P)
(1) (2)
Mixed calibration setup with perspective (P) and telecentric (T) area scan cameras. (1) All perspective cameras are connected by a chain of observation poses that only contains perspective cameras. (2) The second calibration plate (from the left) is not observed by the rightmost perspective camera. Therefore, the relative pose between both perspective cameras cannot be determined uniquely.
Line scan cameras

Setups with telecentric line scan cameras ('line_scan_telecentric'"line_scan_telecentric""line_scan_telecentric""line_scan_telecentric""line_scan_telecentric""line_scan_telecentric") behave identically to setups with telecentric area scan cameras and the same restrictions and ambiguities that are described above apply. For this type of setup, two possible configurations can be distinguished. In the first configuration, all cameras are mounted rigidly and stationary and the object is moved linearly in front of the cameras. Alternatively, all cameras are mounted rigidly with respect to each other and are moved across the object by the same linear actuator. In both cases, all cameras share a common motion vector, which is modeled in the camera coordinate system of the reference camera and is transformed to the camera coordinate systems of all other cameras by the rotation part of the respective camera's pose. This configuration is assumed by default. In the second configuration, the cameras are moved by independent linear actuators in different directions. In this case, each camera has its own independent motion vector. The type of configuration can be selected with set_calib_dataset_calib_dataSetCalibDataSetCalibDataSetCalibDataset_calib_data.

image/svg+xml