get_sheet_of_light_result_object_model_3dGetSheetOfLightResultObjectModel3dGetSheetOfLightResultObjectModel3d (Operator)

Name

get_sheet_of_light_result_object_model_3dT_get_sheet_of_light_result_object_model_3dGetSheetOfLightResultObjectModel3dGetSheetOfLightResultObjectModel3d — Get the result of a calibrated measurement performed with the sheet-of-light technique as a 3D object model.

Signature

get_sheet_of_light_result_object_model_3d( : : SheetOfLightModelID : ObjectModel3D)

Description

The operator get_sheet_of_light_result_object_model_3dget_sheet_of_light_result_object_model_3dGetSheetOfLightResultObjectModel3dGetSheetOfLightResultObjectModel3dGetSheetOfLightResultObjectModel3d returns the result of a fully calibrated sheet-of-light measurement as a 3D object model. The handle of the sheet-of-light model with which the measurement is performed must be passed to SheetOfLightModelIDSheetOfLightModelIDSheetOfLightModelIDSheetOfLightModelIDsheetOfLightModelID. The calibration extent of the sheet-of-light model ('calibration'"calibration""calibration""calibration""calibration") must have been set to 'xyz'"xyz""xyz""xyz""xyz" or 'offset_scale'"offset_scale""offset_scale""offset_scale""offset_scale" before applying the measurement, otherwise the computed coordinates cannot be returned as a 3D object model and an exception is raised.

The handle of the 3D object model resulting from the measurement is returned in ObjectModel3DObjectModel3DObjectModel3DObjectModel3DobjectModel3D. For the 3D points within this 3D object model no triangular meshing is available, therefore no faces are stored in the 3D object model. If a 3D object model with triangular meshing is required for the subsequent processing, use the operator get_sheet_of_light_resultget_sheet_of_light_resultGetSheetOfLightResultGetSheetOfLightResultGetSheetOfLightResult in order to retrieve the 'x'"x""x""x""x", 'y'"y""y""y""y", and 'z'"z""z""z""z" coordinates from the sheet-of-light model and then call the operator xyz_to_object_model_3dxyz_to_object_model_3dXyzToObjectModel3dXyzToObjectModel3dXyzToObjectModel3d with suitable parameters. Refer to xyz_to_object_model_3dxyz_to_object_model_3dXyzToObjectModel3dXyzToObjectModel3dXyzToObjectModel3d for more information about 3D object models.

The unit of the returned coordinates depends on the value of the parameter 'scale''scale''scale''scale''scale' that was set for the sheet-of-light model before applying the measurement. See create_sheet_of_light_modelcreate_sheet_of_light_modelCreateSheetOfLightModelCreateSheetOfLightModelCreateSheetOfLightModel and set_sheet_of_light_paramset_sheet_of_light_paramSetSheetOfLightParamSetSheetOfLightParamSetSheetOfLightParam for details on the possible values of the model parameter 'scale''scale''scale''scale''scale'. The operator get_sheet_of_light_result_object_model_3dget_sheet_of_light_result_object_model_3dGetSheetOfLightResultObjectModel3dGetSheetOfLightResultObjectModel3dGetSheetOfLightResultObjectModel3d returns a handle to an empty 3D object model if the desired result has not been measured yet.

Execution Information

Multithreading type: reentrant (runs in parallel with non-exclusive operators).
Multithreading scope: global (may be called from any thread).
Processed without parallelization.

This operator returns a handle. Note that the state of an instance of this handle type may be changed by specific operators even though the handle is used as an input parameter by those operators.

Parameters

SheetOfLightModelIDSheetOfLightModelIDSheetOfLightModelIDSheetOfLightModelIDsheetOfLightModelID (input_control) sheet_of_light_model → (handle)

Handle for accessing the sheet-of-light model.

ObjectModel3DObjectModel3DObjectModel3DObjectModel3DobjectModel3D (output_control) object_model_3d → (handle)

Handle of the resulting 3D object model.

Result

The operator get_sheet_of_light_result_object_model_3dget_sheet_of_light_result_object_model_3dGetSheetOfLightResultObjectModel3dGetSheetOfLightResultObjectModel3dGetSheetOfLightResultObjectModel3d returns the value 2 (H_MSG_TRUE) if the given parameters are correct. Otherwise, an exception will be raised.