Name
sfs_orig_lrsfs_orig_lrSfsOrigLrsfs_orig_lrSfsOrigLrSfsOrigLr — Reconstruct a surface from a gray value image.
Herror sfs_orig_lr(const Hobject Image, Hobject* Height, double Slant, double Tilt, double Albedo, double Ambient)
Herror T_sfs_orig_lr(const Hobject Image, Hobject* Height, const Htuple Slant, const Htuple Tilt, const Htuple Albedo, const Htuple Ambient)
Herror sfs_orig_lr(Hobject Image, Hobject* Height, const HTuple& Slant, const HTuple& Tilt, const HTuple& Albedo, const HTuple& Ambient)
HImage HImage::SfsOrigLr(const HTuple& Slant, const HTuple& Tilt, const HTuple& Albedo, const HTuple& Ambient) const
HImageArray HImageArray::SfsOrigLr(const HTuple& Slant, const HTuple& Tilt, const HTuple& Albedo, const HTuple& Ambient) const
void SfsOrigLr(const HObject& Image, HObject* Height, const HTuple& Slant, const HTuple& Tilt, const HTuple& Albedo, const HTuple& Ambient)
HImage HImage::SfsOrigLr(const HTuple& Slant, const HTuple& Tilt, const HTuple& Albedo, const HTuple& Ambient) const
HImage HImage::SfsOrigLr(double Slant, double Tilt, double Albedo, double Ambient) const
static void HOperatorSet.SfsOrigLr(HObject image, out HObject height, HTuple slant, HTuple tilt, HTuple albedo, HTuple ambient)
HImage HImage.SfsOrigLr(HTuple slant, HTuple tilt, HTuple albedo, HTuple ambient)
HImage HImage.SfsOrigLr(double slant, double tilt, double albedo, double ambient)
sfs_orig_lrsfs_orig_lrSfsOrigLrsfs_orig_lrSfsOrigLrSfsOrigLr reconstructs a surface (i.e. the relative
height of each image point) using the original algorithm of Lee and
Rosenfeld. The surface is reconstructed from the input image
ImageImageImageImageImageimage. The light source is to be given by the parameters
SlantSlantSlantSlantSlantslant, TiltTiltTiltTiltTilttilt, AlbedoAlbedoAlbedoAlbedoAlbedoalbedo and
AmbientAmbientAmbientAmbientAmbientambient, and is assumed to lie infinitely far away in the
direction given by SlantSlantSlantSlantSlantslant and TiltTiltTiltTiltTilttilt. The
parameter AlbedoAlbedoAlbedoAlbedoAlbedoalbedo determines the albedo of the surface,
i.e. the percentage of light reflected in all directions.
AmbientAmbientAmbientAmbientAmbientambient determines the amount of ambient light falling
onto the surface. It can be set to values greater than zero if, for
example, the white balance of the camera was badly adjusted at the
moment the image was taken.
sfs_orig_lrsfs_orig_lrSfsOrigLrsfs_orig_lrSfsOrigLrSfsOrigLr assumes that the heights are to be extracted on
a lattice with step width 1. If this is not the case, the
calculated heights must be multiplied with the step width after the
call to sfs_orig_lrsfs_orig_lrSfsOrigLrsfs_orig_lrSfsOrigLrSfsOrigLr. A Cartesian coordinate system with the
origin in the lower left corner of the image is used internally.
sfs_orig_lrsfs_orig_lrSfsOrigLrsfs_orig_lrSfsOrigLrSfsOrigLr can only handle byte-images.
- Multithreading type: reentrant (runs in parallel with non-exclusive operators).
- Multithreading scope: global (may be called from any thread).
- Automatically parallelized on tuple level.
Reconstructed height field.
Angle between the light source and the positive z-axis
(in degrees).
Default value: 45.0
Suggested values: 1.0, 5.0, 10.0, 20.0, 40.0, 60.0, 90.0
Typical range of values: 0.0
≤
Slant
Slant
Slant
Slant
Slant
slant
≤
90.0
Minimum increment: 0.01
Recommended increment: 10.0
TiltTiltTiltTiltTilttilt (input_control) angle.deg → HTupleHTupleHTupleVARIANTHtuple (real / integer) (double / int / long) (double / Hlong) (double / Hlong) (double / Hlong) (double / Hlong)
Angle between the light source and the x-axis after
projection into the xy-plane (in degrees).
Default value: 45.0
Suggested values: 1.0, 5.0, 10.0, 20.0, 40.0, 60.0, 90.0
Typical range of values: 0.0
≤
Tilt
Tilt
Tilt
Tilt
Tilt
tilt
≤
360.0
Minimum increment: 0.01
Recommended increment: 10.0
Amount of light reflected by the surface.
Default value: 1.0
Suggested values: 0.1, 0.5, 1.0, 5.0
Typical range of values: 0.0
≤
Albedo
Albedo
Albedo
Albedo
Albedo
albedo
≤
5.0 (lin)
Minimum increment: 0.01
Recommended increment: 0.1
Restriction: Albedo >= 0.0
Amount of ambient light.
Default value: 0.0
Suggested values: 0.1, 0.5, 1.0
Typical range of values: 0.0
≤
Ambient
Ambient
Ambient
Ambient
Ambient
ambient
≤
1.0 (lin)
Minimum increment: 0.01
Recommended increment: 0.1
Restriction: Ambient >= 0.0
If all parameters are correct sfs_orig_lrsfs_orig_lrSfsOrigLrsfs_orig_lrSfsOrigLrSfsOrigLr returns the
value 2 (H_MSG_TRUE). Otherwise, an exception is raised.
estimate_al_amestimate_al_amEstimateAlAmestimate_al_amEstimateAlAmEstimateAlAm,
estimate_sl_al_lrestimate_sl_al_lrEstimateSlAlLrestimate_sl_al_lrEstimateSlAlLrEstimateSlAlLr,
estimate_sl_al_zcestimate_sl_al_zcEstimateSlAlZcestimate_sl_al_zcEstimateSlAlZcEstimateSlAlZc,
estimate_tilt_lrestimate_tilt_lrEstimateTiltLrestimate_tilt_lrEstimateTiltLrEstimateTiltLr,
estimate_tilt_zcestimate_tilt_zcEstimateTiltZcestimate_tilt_zcEstimateTiltZcEstimateTiltZc,
optimize_fft_speedoptimize_fft_speedOptimizeFftSpeedoptimize_fft_speedOptimizeFftSpeedOptimizeFftSpeed
shade_height_fieldshade_height_fieldShadeHeightFieldshade_height_fieldShadeHeightFieldShadeHeightField
3D Metrology